Drilling and Sampling Sample Clauses

The Drilling and Sampling clause defines the procedures and requirements for conducting drilling operations and collecting samples during a project. It typically outlines the methods to be used, the types of samples to be obtained (such as soil or groundwater), and the standards for documentation and handling of those samples. This clause ensures that all drilling and sampling activities are performed consistently and safely, providing reliable data for analysis and minimizing the risk of errors or contamination.
Drilling and Sampling. 1.1.2.1 Drilling and sampling with 3‐inch, thin‐walled tube sampler, continuous to 10.0 ft, 5.0 ft intervals thereafter foot $ 22.00 1.1.2.2 Continuous drilling and sampling with 3‐inch, thin‐ walled tube sampler or split‐spoon sampler foot $ 39.00
View SourceView Similar (2)
Drilling and Sampling. 1.1.2.1 Drilling and Sampling with 3-inch, Thin-Walled Tube Sampler, Continuous to 10.0 ft, 5.0-ft Intervals Thereafter........................................................................................ $ 22.00/foot 1.1.2.2 Continuous Drilling and Sampling with 3-inch, Thin-Walled Tube Sampler or Split-Spoon 1.1.5 Rock Coring, NX or Similar Core Barrel 1.1.5.1 Drilling in Soft Rock (▇▇▇▇▇▇ ▇▇▇▇▇, Eagle Ford Shale, etc.) .................................................................................. $ 30.00/foot 1.1.5.2 Drilling in Hard Rock or Cavitated Rock (Edwards, Buda, ▇▇▇▇ ▇▇▇▇, Georgetown, 1.1.7 Drill Rig Hourly Charges for Boring Layout, Excessive Time Spent Gaining Access to Boring Locations, Move Time, Backfilling Boreholes, Cleaning up Site, Installing Piezometers, and 1.1.9 Cone Penetrometer Testing $3,750.00/day 1.1.10 Wooden Core Boxes (NX) ................................................. .......................................... $ 75.00/each 1.1.11 Field Personnel...................................................................... See 4.0: Engineering Consultation
View SourceView Similar (2)
Drilling and Sampling. Contractor shall be responsible for blasthole drilling and Owner shall approve the drill and/or sampling system being utilized for sampling.
View Source
Drilling and Sampling. 1.1.2.1 Drilling and Sampling with 3-inch, Thin-Walled Tube Sampler, Continuous to 10.0 ft, 5.0-ft Intervals Thereafter........................................................................................ $ 22.00/foot 1.1.2.2 Continuous Drilling and Sampling with 3-inch, Thin-Walled Tube Sampler or Split-Spoon Sampler .............................................................................................................. $ 39.00/foot 1.1.3 Standard Penetration Tests ......................................................................................... $ 27.00/each 1.1.4 TxDOT Cone Penetration Tests.................................................................................. $ 34.00/each
View Source
Drilling and Sampling. This category of service includes subsurface investigations, including drilling and digging test pits. Obtain disturbed and undisturbed samples. Perform field tests such as SPT, Cone Penetration, vane shear, etc. Install and monitor geotechnical monitoring instrumentations, such as piezometer, inclinometer, etc.
View Source

Related to Drilling and Sampling

  • Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.▇▇▇ ▇▇▇▇▇ ▇▇▇▇▇▇▇. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The ▇▇▇▇▇ heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where ▇▇▇▇▇ heights are lower for aesthetic, land treatment, or silvicultural rea- sons.

  • Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until they have received proper training and instruction. (b) The Employer shall provide sufficient and adequate training and/or orientation to any employee working in a new or unfamiliar work area or position.

  • Commissioning Commissioning tests of the Interconnection Customer’s installed equipment shall be performed pursuant to applicable codes and standards. The ISO and Connecting Transmission Owner must be given at least five Business Days written notice, or as otherwise mutually agreed to by the Parties, of the tests and may be present to witness the commissioning tests.

  • Sampling The Licensee agrees that the Composition is purchased as a “Work Made for Hire” whereby the clearing of any sampled materials is the responsibility of Licensee.

  • Synchronization, Commissioning and Commercial Operation 5.1.1 The SPG shall give PGVCL at least thirty (30) days’ advanced preliminary written notice and at least fifteen (15) days’ advanced final written notice, of the date on which it intends to synchronize the Solar Power Project to the Grid System. 5.1.2 Subject to Article 5.1.1, the Power Project may be synchronized by the SPG to the Grid System when it meets all the connection conditions prescribed in applicable Grid Code then in effect and otherwise meets all other Indian legal requirements for synchronization to the Grid System. 5.1.3 The synchronization equipment and all necessary arrangements / equipment including RTU for scheduling of power generated from the Project and transmission of data to the concerned authority as per applicable regulation shall be installed by the SPG at its generation facility of the Power Project at its own cost. The SPG shall synchronize its system with the Grid System only after the approval of synchronization scheme is granted by the head of the concerned substation/ and checking/verification is made by the concerned authorities of the PGVCL. 5.1.4 The SPG shall immediately after each synchronization/tripping of generator, inform the sub-station of the Grid System to which the Power Project is electrically connected in accordance with applicable Grid Code. In addition, the SPG will inject in-firm power to grid from time to time to carry out operational/ functional test prior to commercial operation. For avoidance of doubt, it is clarified that Synchronization / Connectivity of the Project with the grid shall not to be considered as Commissioning of the Project. 5.1.5 The SPG shall commission the Project within nine (9) Months from the Date of execution of this PPA. Declaration of COD shall be certified by the commissioning committee. 5.1.6 The Parties agree that for the purpose of commencement of the supply of electricity by SPG to PGVCL, liquidated damages for delay etc., the Scheduled Commissioning Date as defined in this Agreement shall be the relevant date.