Airworthiness Certification Sample Clauses

Airworthiness Certification. These Implementation Procedures for design approval apply to such aircraft type designs to be type certificated by the FAA and CAAI for standard category airworthiness certification. Standard airworthiness certificates are issued in the normal, utility, acrobatic, commuter, and transport categories of aircraft, as well as for manned-free balloons and special classes of aircraft which include airships, very light aircraft (VLA), gliders, and other non-conventional aircraft. Aircraft for which a special airworthiness certificate is to be issued, will be dealt with on a case-by-case basis through the special arrangements provision in Section V of this document.
View SourceView Similar (8)
Airworthiness Certification. These Implementation Procedures apply to such aircraft type designs to be type certificated by the FAA and the CAA for standard category airworthiness certification. 2.1.1.1 The FAA and the CAA do not normally issue design approvals for products or articles manufactured outside their regulatory jurisdiction unless there is a demonstrated U.S. or New Zealand interest, as the importing State, in issuing the approval. 2.1.1.2 For the FAA, standard airworthiness certificates are issued for aircraft type certificated in the normal, utility, acrobatic, commuter, and transport categories of aircraft, as well as for manned-free balloons and special classes of aircraft which include airships, very light airplanes (VLA), gliders, and other non-conventional aircraft. 2.1.1.3 For the CAA, standard airworthiness certificates are issued for aircraft that are type certificated in the normal, utility, acrobatic, commuter and transport categories. 2.1.1.4 Aircraft for which a special airworthiness certificate is issued by the FAA or a special category airworthiness certificate is issued by the CAA will be dealt with on a case-by-case basis through the special arrangements provision in Section IX of this document.
View SourceView Similar (7)
Airworthiness Certification. The Seller represents and warrants that each Material is manufactured under an approval granted or accepted by the FAA under 14 C.F.R. Part 21 of the Federal Aviation Regulations. Upon delivery to the Buyer, the Seller will provide with each Material a certification that the Material has been approved or accepted by the FAA under 14 C.F.R. Part 21. Acceptable certification documents include the following: • Federal Aviation Administration – FAA Form 8130-3 Airworthiness Approval Tag • Joint Aviation Authorities – JAA Form One Authorized Release Certificate • European Aviation Safety Agency – EASA Form One Authorized Release Certificate • Transport Canada – TC Form 24-0078 Authorized Release Certificate • A Certificate of Conformance or Material Certification Document that lists the parts by Manufacturer’s part number and condition, and contains a signed statement certifying that such parts are aeronautical replacement parts listing the specific FAA approval or acceptance criteria applicable to such parts. To meet the above criteria, it is permissible for the Seller to provide the Buyer with copies of certification documents originally supplied to the Seller with shipments of Material prior to the transfer of the Material to the Buyer. The original certification documents are required to meet certification requirements stated above and the original copies, if not provided to the Buyer with the shipments, will remain on file at the Seller’s facility.
View SourceView Similar (3)
Airworthiness Certification. These Implementation Procedures for design approval apply to such aircraft type designs to be type certificated by the FAA and JCAB for standard category airworthiness certification. Aircraft for which a special airworthiness certificate is to be issued will be dealt with on a case-by-case basis through the special arrangements provision in Section V of this document.
View SourceView Similar (3)
Airworthiness Certification. These Implementation Procedures for design approval apply to such aircraft type designs to be type certificated by the FAA and for standard category airworthiness certification. Standard airworthiness certificates are issued in the normal, utility, acrobatic, commuter, and transport categories of aircraft, as well as for manned-free balloons and special classes of aircraft which include airships, gliders, and other non-conventional aircraft. Aircraft for which a special airworthiness certificate is to be issued, will be dealt with on a case-by-case basis through the special arrangements provision in Section 5 of this document.
View SourceView Similar (2)
Airworthiness Certification. The Contractor shall maintain OEM and FAA certifications for the repair of all components related to the RSS for the Period of Performance (POP) prescribed herein. The Contractor shall immediately notify the Contracting Officer of the loss of either certification. The Contractor shall ensure software versions are noted distinctly on all equipment documents including inventory management documents and any reports required by the SOW.
View Source
Airworthiness Certification. These Implementation Procedures for design approval apply to such aircraft type designs to be type certificated by the FAA and CAA for standard category airworthiness certification. For the FAA, standard airworthiness certificates are issued in the normal, utility, acrobatic, commuter, and transport categories of aircraft, as well as for manned-free balloons and special classes of aircraft which include airships, very light aircraft (VLA), gliders, and other non-conventional aircraft. For the CAA, standard airworthiness certificates are issued for aircraft that are type certificated in the normal, utility and acrobatic categories. Aircraft for which a special airworthiness certificate is issued by the FAA or a restricted or special category airworthiness certificate is issued by the CAA will be dealt with on a case-by-case basis through the special arrangements provision in Section V of this document.
View Source
Airworthiness Certification. The FAA will provide initial airworthiness approvals as required to meet either baseline or PSSA program needs. Airworthiness approvals to be issued include:
View Source

Related to Airworthiness Certification

  • Certification of Compliance The Recipient shall complete and submit the following Notice of Completion and, if applicable, Engineer’s Certification of Compliance to the Department upon completion of the construction phase of the Project.

  • AS9100 Certification ‌ AS9100 Certification, specifies requirements for a quality management system to demonstrate the Contractor’s ability to consistently meet the customer requirements as well as statutory and regulatory requirements for the aerospace industry. An AS9100 Certification, is not mandatory; however, Contractors who desire to compete for work within the aerospace industry are encouraged to have AS9100 Certification, during the entire term of OASIS. The Contractor shall notify the OASIS CO, in writing, if there are any changes in the status of their AS9100 Certification, and provide the reasons for the change and copies of audits from an AS9100 Certification Body, as applicable. If only part of a Contractor’s organization is AS9100, certified, the Contractor shall make the distinction between which business units or sites and geographic locations have been certified.

  • CHILD SUPPORT CERTIFICATION Under Section 231.006, Texas Family Code, the Engineer certifies that the individual or business entity named in this contract, bid, or application is not ineligible to receive the specified grant, loan, or payment and acknowledges that this contract may be terminated and payment may be withheld if this certification is inaccurate. If the above certification is shown to be false, the Engineer is liable to the state for attorney’s fees, the cost necessary to complete the contract, including the cost of advertising and awarding a second contract, and any other damages provided by law or the contract. A child support obligor or business entity ineligible to receive payments because of a payment delinquency of more than thirty (30) days remains ineligible until: all arrearages have been paid; the obligor is in compliance with a written repayment agreement or court order as to any existing delinquency; or the court of continuing jurisdiction over the child support order has granted the obligor an exemption from Subsection (a) of Section 231.006, Texas Family Code, as part of a court- supervised effort to improve earnings and child support payments.

  • Recertification Upon expiration of the time period which the health care provider originally estimated that the employee needed for his/her own serious health condition, the City may require the employee to obtain recertification if additional leave is requested.

  • Medical Certification (1) The University may require an employee to provide medical certification from a health care provider for FMLA leave without pay when taken for the serious health condition of the employee or the employee's family member. (2) Medical certification may be required to affirm the employee's ability to return to work and perform one or more of the essential functions of the job within the meaning of the Americans with Disabilities Act (ADA), after being absent on FMLA leave.