Design and Engineering Services Sample Clauses
POPULAR SAMPLE Copied 6 times
Design and Engineering Services. 10.1 Seller will provide the Services in accordance with the requirements of good and sound workmanship. The Services shall be based on the information provided by the Customer, whereby the Customer guarantees the accuracy and completeness thereof. All consequences of inaccuracy and/or incompleteness of such information are entirely at the Customer’s expense and risk.
10.2 The Services are always project specific and based on the purchase and application of the Products produced and/or delivered by or on behalf of Seller. The Customer is not permitted to use the Services provided by Seller with the application of third-party materials, at any rate the consequences of such a course of action are entirely at the Customer’s expense and risk.
10.3 IP rights (as defined in clause 18) relating to the Services, including associated methodologies, techniques, documents and other information or knowledge are and continue to be vested in Seller. To the extent necessary for this purpose, the Customer will obtain a non-transferable, non-exclusive and free licence for the agreed use of these rights for the duration of the Agreement.
Design and Engineering Services. The Consultant shall perform site planning and analysis and design services for the Project as provided in Exhibit A. As Project requirements are sufficiently identified, the Consultant shall periodically update the schedule in Exhibit E to identify milestone dates for decisions required of the Owner and design services furnished by the Consultant. Such updates shall not change task completion dates, unless the Owner grants written approval for such changes. Based on the approved program, and the Project Schedule the Consultant shall prepare, for approval by the Owner, Design Documents, developed in stages to the twenty five (25%) consistent with the applicable procedures and standards of the Mass Highway 2006 Project Development and Design Guide, inclusive of drawings prepared on a CADD system and other documents illustrating the complete design. The Consultant shall prepare such studies or other materials as are necessary to establish the design of the Project. Upon proper authorization and notice to proceed the Consultant shall prepare, for approval by the Owner, Design Documents with the one hundred percent (100%) level of complete design development. The Owner has provided to the Consultant, and the Consultant has in its possession, certain information concerning existing conditions at the site tasks associated with Section 100: Project Development Engineering of the MassDOT – Highway Divisions Scoping Workbook Project, including the documents and information listed on Exhibit G. The Consultant shall review all such information, verify, in general, the accuracy of such information, and notify the Owner of any inconsistencies or discrepancies observed by the Consultant.
Design and Engineering Services. Party B will provide to Party A design and engineering services for the development of *** for a period of 2 years from the date of the Localization Agreement. The activities in furtherance of such services are anticipated to begin on January 1, 2017, in accordance with the provisions of Appendix E. The Parties will work together, on a cost-sharing basis and in good faith, to pursue additional design and engineering services based upon a mutually agreed upon product roadmap and under a separate agreement articulating the applicable terms and conditions.
Design and Engineering Services. Contracting Party has contracted with the Project Architect and with all such other architects and engineers (collectively, the “Design and Engineering Professionals”) as may be necessary for the engineering and design services necessary for the completion of the Theater Phase (collectively, the “Design and Engineering Services”), the cost of which shall be included as a Project Cost. Notwithstanding the retention of Design and Engineering Professionals by Contracting Party, the Project Architect shall retain ultimate authority and responsibility as to coordination and resolution of any conflicts that may arise between the respective Design and Engineering Professionals and the Design and Engineering Services to be rendered and shall have final approval rights as to the aesthetic components of the Theater Phase subject to any approval rights granted to the Oversight Committee pursuant to Sections 10.1, 10.2 and 10.3 below.
Design and Engineering Services. 5.7.1 Redeveloper’s Engineer and Other Professionals. Design and engineering services relating to the Phase 1 Infrastructure Improvements and the Phase 1 Infrastructure Project shall be provided on behalf of the Redeveloper by the Redeveloper’s Engineer and Other Professionals retained by Redeveloper, or by a Third Party Utility Provider’s engineer or other professionals, or the Redeveloper may request that the Project Manager provide such engineering services. All Final Plans and Specifications shall be executed, certified, or sealed, by the Redeveloper’s Engineer, the Project Manager, such Other Professionals, or by a Third Party Utility Provider’s engineer or other professionals, as applicable.
Design and Engineering Services to further develop the technical scope of the Project, enhance Project value and define the Project budgetary and finance requirements and finalise all the technical details in order for the EPC contractors to provide binding offers.
Design and Engineering Services. The Consultant shall perform site planning and analysis and design services for the Project as provided in Exhibit A. As Project requirements are sufficiently identified, the Consultant shall periodically update the schedule in Exhibit E to identify milestone dates for decisions required of the Owner and design services furnished by the Consultant. Such updates shall not change task completion dates, unless the Owner grants written approval for such changes. Based on the approved program, and the Project Schedule the Consultant shall prepare, for approval by the Owner, Design Documents, developed in stages to the twenty five (25%) and twenty five (25%) to the one hundred percent (100%) level of complete design development consistent with the applicable procedures and standards of the Mass Highway 2006 Project Development and Design Guide, inclusive of drawings prepared on a CADD system and other documents illustrating the complete design. The Consultant shall prepare such studies or other materials as are necessary to establish the design of the Project. Upon proper authorization and notice to proceed the Consultant shall prepare, for approval by the Owner, Design Documents with the one hundred percent (100%) level of complete design development. The Owner has provided to the Consultant, and the Consultant has in its possession, certain information concerning existing conditions at the site tasks associated with Section 100: Project Development Engineering of the MassDOT – Highway Divisions Scoping Workbook Project, including the documents and information listed on Exhibit G. The Consultant shall review all such information, verify, in general, the accuracy of such information, and notify the Owner of any inconsistencies or discrepancies observed by the Consultant.
Design and Engineering Services. The Consultant shall perform site planning and analysis and design services for the Project as provided in Exhibit A.
Design and Engineering Services. TEPPCO shall provide or cause to be provided all design and engineering services needed to fully define the Pipeline Facilities and to cause the Pipeline Facilities, as designed and engineered, to comply with the Completion Standards and to operate in accordance with the Performance Standards. Such design and engineering services shall include but not be limited to the services described in Attachment 2.1 attached hereto. All such services shall be performed in accordance with the Project Schedule.
Design and Engineering Services. SWE shall be responsible for carrying out the following services as required by Halton Hills in conjunction with the design and engineering of any component of the Lighting system:
(i) Preparation of lighting designs for streetlight or walkway/trail lighting installations with design and approval by a Professional Engineer. Prior to commencing the lighting design, SWE shall provide Halton Hills with a quotation fee for the lighting design services for review and approval;
(ii) New designs shall conform with the Illuminating Engineering Society’s Roadway Lighting ANSI/IES RP-8-18 standards;
(iii) Assist Halton Hills to develop legal agreements for the construction of the Lighting System;
(iv) Submit lighting designs to Halton Hills for review and comment prior to installation;
(v) Participate with Halton Hills in meetings for information, negotiation or presentation in connection with design criteria, standards or detailed designs; and
(vi) Maintain complete and accurate records of time spent on the design preparation by SWE staff for Work that will be billed to Halton Hills.