Process Control Clause Samples

Process Control. Supplier shall control the quality and strive for the continuous improvement of its manufacturing processes and those of its subcontractors through the use of monitoring techniques and tools in Supplier’s reasonable business judgment, which may include: process-flows, Root Cause Analysis, capability studies, risk analysis, failure mode and effect analysis, reliability calculations, measurement system analysis, gage R&R studies, statistical process control (SPC), corrective actions and preventative actions, and process and product audits. Supplier shall establish and maintain a quality measurement system and quality analysis process as determined in Supplier’s reasonable business judgment, executed by appropriately skilled personnel. Supplier approach and results will be communicated to Distributor in a mutually agreed format on a quarterly basis. This report at minimum shall contain mutually agreed data, CAPA plans and results. Supplier will be fully responsible to ensure that all process changes affecting Products, including process or design changes, changes to manufacturing processes (including geographic location) changes affecting electrical performance, mechanical form or fit, function, environmental compatibility, chemical characteristics, life, reliability or quality of Products or changes that could have significant impact upon Supplier’s quality system will be in accordance with this Attachment. Supplier shall provide to its employees training courses to ensure that Supplier’s employees keep abreast of technical, regulatory and other developments as determined in Supplier’s reasonable business judgment.

Process Control. ‌ Developer shall plan and control the Work and when necessary shall prepare a documented process plan defining how work is to be carried out. Documentation may be in the form of a narrative, flow chart, or control points. Developer shall identify and plan the production, installation, and servicing processes that directly affect quality and shall ensure that these processes are carried out under controlled conditions.

Process Control. (a) Operator shall operate and maintain the Facilities and all equipment and processes contained therein in accordance with relevant operation and maintenance manuals for the Facilities, Applicable Law, and the Environmental Permits. (b) During any Municipality-approved construction or other modification of the Facilities, Municipality and Operator will work together to maintain Operator’s access to the Facilities and to minimize disruption and outages to the Facilities’ existing equipment and components. Municipality and Operator will jointly develop a plan of action that will address protection to the Facilities’ equipment and processes during any such construction and/or other rehabilitation period while providing for the continued operation of the Facilities to the extent reasonably possible.

Process Control. Encision shall follow documented processes during assembly of the Products and keep written records of all assembly and tests performed as determined by Encision’s Quality Systems Procedures.

Process Control. Supplier processes (heat treat, plating, patch, etc.) shall be validated at the supplier via in process monitoring (setup, hourly, end of run inspections per the supplier’s control plan), in addition to any specified lot certification testing requirements called out by AlphaUSA print or specifications. These instructions should be derived from sources such as the purchase agreement, quality plan, the control plan and the product realization process if applicable. Data collection worksheets are at the discretion of the supplier unless otherwise required.

Process Control. Supplier shall make no change in material or supply chain used, construction or fabrication techniques, test methods used without prior written approval of Buyer. Any such changes desired by the Supplier shall be requested in writing indicating reason for such change and including effect on cost and performance.

Process Control. 5.4.19.1 The Contract manufacturer will implement production process control measurements with SMT Reflow profile and Solder Wave profile measurements before start production, AOI 100% for SMT, X-Ray of Lead Less components and BGA according to sample 0.2%, Conformal Coating thickness sample 3 times during production batch, PCBA ion contamination after cleaning process 1 time per production batch, Product sealing sample 1%, monitor the process materials and react with correction action in case any of the results are out of control limits.

Process Control. Seller shall use process control techniques for all identified characteristics noted on purchase order, engineering drawings, manufacture, and quality plans. Seller shall maintain records subject to Buyer review and furnish copies of charts or graphs used in process control with shipment. Seller shall utilize continuous improvement techniques relevant to their part and Quality System processes.

Process Control. NTC’s Access Personnel shall have the Right of Access to the Manufacturing Plant pursuant to Section 3.2. At all times during the production, manufacture, packaging and distribution of the NTC Products, Access Personnel shall have the right to observe and inspect the processes, methods, techniques, actions and activities utilized by SM’s employees or agents used during the production, manufacture, packaging and distribution of the NTC Products in order to meet the requirements of SM hereunder. NTC and/or SM, as appropriate, in conjunction with the other party hereto, will take corrective measures for any instance in which the NTC Product falls outside the Specifications.