Release Control Sample Clauses

The Release Control clause defines the procedures and conditions under which control over a product, service, or information is formally transferred from one party to another. Typically, this clause outlines the steps required for release, such as inspections, approvals, or documentation, and may specify who is authorized to grant or accept control. Its core practical function is to ensure a clear and documented handover process, minimizing disputes and misunderstandings about responsibility and ownership at the point of transfer.
Release Control. 1. The Contractor should coherently group software changes into staged, planned releases. 2. Release control shall ensure that Contractor software released from the development environment is adequately specified in terms of documentation, testing and quality. 3. The release control procedure used by the Contractor shall address: • Configuration management: Management of the resources used to control acceptance of new/changed software into the application libraries. Such configuration management needs to permit regression back to any previous build release. It should be possible to determine the modification state of a particular software component in any new release. This principle similarly applies to hardware changes. • Document Management: Generation of release notes and document updates for the configuration controlled items. Ref: INMARSAT GLOBALISED VOICE Issue: Draft V2.8h Date: Page: 59 of 81 Inmarsat Globalised Voice Project 06-4318 Statement of Work • Testing: Ensuring that new/changed functions are individually tested then regression tested within the complete release using a representative test environment. • Production: Generation of release media or hardware components for site installation. • Installation instructions: Producing appropriate and documented installation guidelines to the host sites which will, in case of unforeseen problems, allow the staff, in a reasonable time scale, to regress to the previous release. • Certification: Ensuring that the site configurations are compatible with the new software or hardware release, in terms of configuration item compatibility and operating system parameters. 4. The type of a release shall be mutually agreed between the Contractor and nominated Inmarsat representative(s). 5. The type of release shall be categorised as: • Routine: Where installation procedures are provided with the release. In this event, each release represents a localised, low risk change rectifying a well defined problem.
View SourceView Similar (2)
Release Control. 1 2.5 [**]............................................................ 1 2.6 Data Interfaces................................................. 1 2.7 Existing or New Application Software Integration................ 1 2.8
View Source
Release Control. 1. The Contractor should coherently group software changes into staged, planned releases. 2. Release control shall ensure that Contractor software released from the development environment is adequately specified in terms of documentation, testing and quality. 3. The release control procedure used by the Contractor shall address: 3.1. Configuration management: Management of the resources used to control acceptance of new/changed software into the application libraries. Such configuration management needs to permit regression back to any previous build release. It should be possible to determine the modification state of a particular software component in any new release. This principle similarly applies to hardware changes.
View Source
Release Control. Contractor release control shall be applied to ensure that software released from the development environment is adequately specified in terms of documentation, testing and quality.
View Source

Related to Release Control

  • Site Control In the total loss of building use scenario, what likely exists will be a smoking pile of rubble. This rubble will contain many components that could be dangerous. It could also contain any personnel on the premises at the time of the disaster. For these reasons, the local fire marshal with the assistance of the police will control the site until the building is no longer a threat to surrounding properties and the companies have secured the site from the general public. During this time, the majority owner of the building should be arranging for a demolition contractor to mobilize to the site with the primary objective of reaching the cable entrance facility for a damage assessment. The results of this assessment would then dictate immediate plans for restoration, both short term and permanent. In a less catastrophic event, i.e., the building is still standing and the cable entrance facility is usable, the situation is more complex. The site will initially be controlled by local authorities until the threat to adjacent property has diminished. Once the site is returned to the control of the companies, the following events should occur. An initial assessment of the main building infrastructure systems (mechanical, electrical, fire and life safety, elevators, and others) will establish building needs. Once these needs are determined, the majority owner should lead the building restoration efforts. There may be situations where the site will not be totally restored within the confines of the building. The companies must individually determine their needs and jointly assess the cost of permanent restoration to determine the overall plan of action. Multiple restoration trailers from each company will result in the need for designated space and installation order. This layout and control is required to maximize the amount of restoration equipment that can be placed at the site, and the priority of placements. Care must be taken in this planning to ensure other restoration efforts have logistical access to the building. Major components of telephone and building equipment will need to be removed and replaced. A priority for this equipment must also be jointly established to facilitate overall site restoration. (Example: If the AC switchgear has sustained damage, this would be of the highest priority in order to regain power, lighting, and HVAC throughout the building.) If the site will not accommodate the required restoration equipment, the companies would then need to quickly arrange with local authorities for street closures, rights of way or other possible options available.

  • Erosion Control a. The Purchaser shall construct slash and debris erosion barriers, dips, water bars or ditches in skid trails and landings as directed by the Forest Officer. b. The kinds and frequency of erosion control structures shall be adjusted to soil types, topography and climatic conditions as directed by the Forest Officer. c. The Purchaser is required to recontour any excavated skid trails, and provide for effective erosion control in the trail location as directed by the Forest Officer. d. Erosion control work shall commence as soon as skidding is completed on each skid trail or landing, and must be kept current with unit operations. e. Erosion control work shall be completed and approved by the Forest Officer in unfinished units before operations cease for inactive periods including heavy winter snowfall, spring breakup and restricted dates. f. All erosion control work in each unit shall be completed prior to notification pursuant to Section VII.M.7.

  • Weed Control The tenant shall control all noxious weeds on the subject lands and maintain any summerfallow in a reasonably weed free condition.

  • Control Notwithstanding any other provision of the Agreement, it is understood and agreed that the Trust shall at all times retain the ultimate responsibility for and control of all functions performed pursuant to this Agreement and has reserved the right to reasonably direct any action hereunder taken on its behalf by the Sub-Adviser.

  • Climate Control a. The air conditioning/heating units shall be functional at all times. b. The air discharged from the air conditioner interior vent system shall be continuously cool. c. All air conditioning temperature controls and functions shall operate as originally designed and manufactured with no knobs or components broken or missing. d. Systems shall operate on all OEM speeds with no excessive noise.