Electrical connection Clause Samples

Electrical connection. 12.1. The Developer shall deliver to the Purchaser, at the expense of the Developer, a Section 31 certificate of electrical compliance and electrical connection, such certificate to be delivered to the Purchaser on the Transfer date. 12.2. The Purchaser shall arrange for the connection of electricity directly from Drakenstein Municipality.

Electrical connection. Only qualified electricians may carry out electrical works to the pump or the controls. Before carrying out any work, pull out the mains plug and ensure that the power supply to the unit cannot be switched on again by anyone else. The standards applicable in each case (e.g. EN), the country-specific regulations (e.g. VDE in Germany), and the regulations of the local supply network operator must be ob- served. Observe the operating voltage (see the type plate)! The units have a level controller that switch- es the pump on and off depending on the lev- el of the water. An integrated alarm system beeps if there is a malfunction, even if this is only temporary. If the pump overheats, the motor cuts out due to the winding thermostat. After the thermostat has switched off the system, pull out the mains plug before remedying the fault, since the device can switch itself on again automatically if the power is still con- nected. A direct malfunction message is not generated. Only connect the pump to electrical sockets that have been installed properly in a dry room, above the backup level, in accordance with the regulations, and are fitted with at least a 16 A (delay) fuse.

Electrical connection. Inverters & Combiner Box a. Verify condition of inverters. b. Clean filter(s) and vacuum interior. c. Note condition of all circuit boards and electrical components. d. Check Voc & Isc of all strings (if required). e. Verify that all manufacturer updates and service bulletins have been performed. f. Coordinate inverter manufacturer service, if necessary. g. Perform all electrical connection torque tests. h. Inspect and clean heatsink, if applicable. i. Inspect and clean inverter exhaust fan a vents. j. Inspect and treat enclosure seal. Reseal if necessary. k. Inspect and tighten connectors and lugs (inverter, transformer, disconnects). l. Oil and lubricate disconnects. m. Check all fuses for cleared fuse and replace any cleared fuses. n. Verify condition of wire transition junction boxes for weatherproofing, corrosion, and security of internal wiring connections. o. Verify condition of all DC and AC conduits and connections. p. Verify interior and exterior condition of DC combiner box(es).

Electrical connection. ▇▇▇▇▇▇’▇ team partner, ▇▇▇▇▇▇ Electric, will provide electricians for final electrical connection and disconnection to the requestor facility(s). An example of electrical interface and start-up procedures are listed as follows:

Electrical connection. 1. The Certificate Holder shall pay the cost of re-conductoring the 12.47 kV 3-phase line extending from the south sub-station to ▇▇▇ ▇▇▇▇▇▇▇▇ Avenue. 2. The Certificate Holder shall also pay the cost to obtain and install a pad- mounted switch (equivalent to S&C Model 662-32) at a location determined by the City of Sumas adjacent to the Generation Facility in order to provide safe management of the electric utility in the vicinity of the Site.

Electrical connection. Inverters & Combiner Box a. Verify condition of inverters. b. Note condition of all circuit boards and electrical components. c. Check Voc & Isc of all strings (if required). d. Verify that all manufacturer updates and service bulletins have been performed. e. Coordinate inverter manufacturer service, as necessary. f. Perform all electrical connection torque tests. g. Inspect and clean heatsink, if applicable. h. Inspect and clean inverter exhaust fan and vents. i. Inspect and tighten connectors and lugs (inverter, transformer, disconnects). j. Check all fuses for cleared fuse and replace any cleared fuses. k. Verify condition of wire transition junction boxes for weatherproofing, corrosion, and security of internal wiring connections. l. Verify condition of all DC and AC conduits and connections.

Electrical connection. A standard six-pin connector comes wired to your travel trailer using the following standard color code.

Electrical connection. 32 6.8 Menu Definition...........................................................................................33 6.8.1 Ready State...........................................................................................33 6.8.2 Menu State............................................................................................33 6.8.3 Configuration Mode....................................................................................34 6.8.4 Service Diagnostics Mode..............................................................................34

Electrical connection. 1. The Company will supply the Tenant, for its account, a feed switch to which the Tenant will connect. The electricity supply line will suit, from an engineering point of view, the full electrical load of the premises. 2. The main electrical board will comply with the requirements of the standard. 3. The size of the electrical supply feed to the Tenant will be 3 * 600 Ampere. 4. In the event that the Tenant will require a larger electricity supply feed than that stipulated in Paragraph 2 above, the Tenant will bear the addition to the price between the expanded electricity supply line and that stipulated in paragraph 2 above, pursuant to the Israel Electric Corporation price list as will be valid at the time. 5. Changes to the existing electrical facility and the power and lighting electrical boards in the area of the premises will be carried out by the Tenant and for the Tenant’s account. 6. Prior to commencing changes in the execution of the existing electrical facility that the Tenant wishes to install in the premises, the Tenant will submit detailed electrical plans of the facility to the Company for approval. Only after obtaining authorization, can the Tenant commence carrying out the work in the premises. 7. Upon the completion of the execution of the Tenant’s electrical connection, the Tenant will order an inspection of the facilities by a qualified electrical inspector and will produce a report for the Company that confirms that the facility complies with the requirements of the Israel Electric Corporation and is free of defects and can be connected to the electricity supply. To: Tefen Enterprises Ltd. Company No. ▇▇-▇▇▇▇▇▇-▇ P. O. Box 1, Tefen 24959 (Hereinafter “The Company”) Dear Sir / Ma’am, We hereby confirm that as of [date] ___________ and up to [date] ____________ our company has drawn up contractor work insurance in the name of the Tenant, contractors and subcontractors, which secures the work carried out by the Tenant and / or anyone acting on behalf of the Tenant as detailed below, of a scope of cover that is not less than the cover pursuant to the wording of the policy known as “Bit” customary at the date of the commencement of the insurance period: Name of the insured in all the insurance policies: The contractor and / or the Tenant and / or contractors and / or subcontractors. 1. Chapter 1 – “All Risks” insurance that covers loss or damage caused to the Tenant’s work, of full value, as well as loss or damage caused to the equipment u...