System Setup Sample Clauses

System Setup. A schematic representation of the different gas/liquid systems are depicted in Fig.

System Setup. The tasks in system setup include designing and finalizing the technical specification for the system, defining the processes used in the system, and specifying any requirements for operating the system. For example, a blockchain governing body (the Governing Body in the present document) needs to define the process for incorporating a new consensus node operator. Or, the governing body needs to set the security requirements an entity must meet in order to host a consensus node. The creation of the present document can be viewed as a system setup task. Other setup tasks include defining system roles and responsibilities as well as the mechanism for authorization and revocation of such roles and responsibilities.

System Setup. KGC chooses a random number

System Setup. Given security parameter 1k, the KGCs generates two groups G1, G2, and an admissible bilinear map eˆ : G1 × G1 −→ G2, where G1 denotes a cyclic additive group of prime order q and G2 is a multiplicative group of the same order. The KGCs chooses a generator P of G1 and publishes the system parameters params = {G1, G2, eˆ, P, H1, H2, H3}, here H1 : {0, 1}∗ → Z∗, H2 : G2 → Z∗, H3 : Z∗ × Z∗ → Z∗ are cryptographic hash own subgroup key. Thus, when a member joins or leaves functions. the communication group, it joins or leaves only its lo- cal subgroup. As a result, only the local subgroup com- munication key needs to be refreshed and the scalability problem is greatly mitigated. We use a ’group’ of key generation centers (KGCs) to share the overall key gener- ation and distribution workload. In our scheme the task The basic idea of our scheme is the usage of an iden- tity tree, where each node in the tree has an identity. The leaf node’s identity is corresponding to a user’s iden- tity and the interior node’s identity is generated from it’s children’s identity. Figure 4 shows an example of identity tree. A node in the identity tree is also associate with a sv)−1P and the node N 1’s private key P 1 = (Q1 +sω)−1P

System Setup. Input/Modify all data that is specific to the project’s intersections, with all available graphics. Create intersection diagrams to facilitate optimization of the system. Program system to report the following events, at a minimum: • Traffic Signal Flash (Conflict or Manual) • Detector Failure • Communication Failure • Cabinet Door Open (if equipped with door switch) • Any additional events requested by the municipalities or PennDOT that can be accommodated by the software

System Setup. The temporary vehicle tracking devices attached to the SamTrans sub-fleet will be configured to send location updates to the LYT cloud platform. Software will collect and process transit bus location updates in real-time. Once approximately 5 weeks of transit bus location information has been saved, LYT will begin training machine learning models capable of predicting the buses arrive time to the piloted traffic signals. The City of East Palo Alto will provide LYT with traffic signal phase diagrams according to the NEMA standard. EPA and Cal-West IT will work with LYT to implement secure communication between traffic signals, Maestro, and the cloud platform. Figure 6: LYT.speed Network Architecture Diagram The LYT system includes a web portal for EPA, C/CAG and transit staff to login and view how the transit system is performing at each of the piloted traffic signals. Features include: • Secure login with additional One Time Password (OTP) at each login • View entire city, multiple cities, a particular signal or a particular transit vehicle • Troubleshoot issues in real-time at the intersection level with signal performance metrics • Review charts of daily priority calls and their impact on transit performance Summarized in the table below, a number of significant metrics will be collected during the pilot time to evaluate the level of success, including, but not limited to: • Setup and installation time • Traffic light delay • Bus speed • Traffic signal network performance Using this information SSV and LYT will provide to all stakeholders a comprehensive report which will include, but is not limited to, the analysis and documentation of: • The security & reliability of the traffic signal communication network • The before and after effects of traffic light delay on average bus speed • Report will document the project challenges • Recommendations on next steps • Potential to add other project evaluation elements into the report Other project-related data and metrics may be added to the report, based on evolving requests from stakeholders and participants. SSV shall submit a report outline to C/CAG for approval prior to drafting the report. SSV will also submit a draft project report to all the partners for comments. With comments from the stakeholders, SSV will then prepare a final project report for submittal to C/CAG. ITEM # TASKS AND DELIVERABLES ANTICIPATED SCHEDULE 1 LYT and Cal-West to verify traffic signal interconnect possible using 4G wireless mo...

System Setup. Customer agrees to maintain an adequate staff of persons who are knowledgeable with the systems currently used by Customer to process data. Customer further agrees to cooperate fully with any reasonable requests of Cardinal necessary to complete the deployment and conversion in a timely and efficient manner. Cardinal will provide Customer written network and equipment specifications for proper operation of the Software. Customer is responsible for procuring and installing the appropriate equipment in accordance with Cardinal’s specifications, including cabling and any configuration or telecommunications changes required for communications, to enable Customer’s proper use of the Software as well as remote access to the Software by Cardinal for the remote performance of Maintenance Services.

System Setup. Take the security parameter 𝜅 as input, the trust participant cloud server (𝐶𝑆) generates a multiplicative cyclic group 𝐺 of 𝑞 order with a generator 𝑔. Next, 𝐶𝑆 chooses a random number 𝑥 as the master private key, sets the system public key 𝑔𝑃𝑢𝑏 = 𝑔𝑥. And then chooses five hash functions 𝑞 𝐻1 , 𝐻2 , 𝐻3 , 𝐻4 and 𝐻5 , where 𝐻1 :{0,1}∗ → 𝑍∗ , 𝐻2 :𝐺 → 𝑆𝐾𝑈𝑖 to the 𝑈𝑖 through a secure channel.

System Setup. A. UNIT ID NUMBER I. Every PDR-2000 is assigned a Unit ID number whether or not the Unit ID feature is used. The current Unit ID number assigned to the unit can be found in the top left corner of the Default display. It is important that no unit be assigned number 00. The unit will not operate correctly with a Unit ID number 00. II. To enter a new Unit ID number, enter a two digit number from 01 to 99 (01 to 03 for units equipped with an Audio Communications module) and press F1 (OK). To exit without changing the number, press F4 (Exit). III. To turn the Unit ID feature On/Off press 1 then F1 (OK) to enter the Unit ID menu again. The * will show if the Unit ID is currently On or Off. To change this setting press 1 then F1 (OK). The next menu offers the On/Off choice. Again the * shows the current setting. Press 1 for On and 2 for Off then press F1 (OK). IV. Press F4 (Exit) to return to the System Settings menu. B. PASSWORD I. Press 2 and F1 (OK) to enter the Password menu. II. The current password is displayed. Enter a new 4 digit number (do not use Function keys) for the password and press F1 (OK) to change the password. Repeat the number to confirm and press F1 (OK). Press F3 (Clr) to erase an entry on the display. Press F4 (Exit) to exit without making a change to the password.