DIMENSIONAL STANDARDS Clause Samples

The Dimensional Standards clause establishes the required measurements and tolerances for materials, components, or finished products specified in a contract. It typically outlines the acceptable ranges for dimensions such as length, width, height, or thickness, and may reference industry standards or specific technical drawings. By clearly defining these parameters, the clause ensures that all parties have a mutual understanding of the physical requirements, reducing the risk of disputes over nonconforming goods and helping to maintain quality control throughout the project.
DIMENSIONAL STANDARDS. LOT SIZE/SET BACKS/HEIGHT: Project Size: The Project is 8.20 acres.
View SourceView Similar (2)
DIMENSIONAL STANDARDS. Consistent with BDMC 18.66.020(A) (Exhibit “E”) and RCW 36.70B.170, Condition of Approval No. 144 of the MPD Permit Approval provides that: “Front yard setbacks and other specific lot standards shall be determined as part of the Development Agreement.” This subsection outlines the dimensional standards applicable within the Project Site consistent with the MPD Permit Approval to impose restrictions beyond the City’s applicable code provisions.
View SourceView Similar (2)
DIMENSIONAL STANDARDS. Non-residential Min. Lot size n/a Min. Lot width n/a Maximum FAR 0.25 Max Building Height 45’ Setbacks (Building and Truck Loading Areas) • Interior Lot lines • Internal Roads • Palm Coast Parkway Arbor Trace Property Line • Old Kings Road • Florida Park Drive 0’ 20’ 35’ 25’ 35’ 35’
View SourceView Similar (2)
DIMENSIONAL STANDARDS. The following dimensional standards shall apply in the ▇▇▇▇▇▇▇ Center Contract Zone: (a) Minimum Lot Size: 50,000 square feet (b) Net Residential Density: 40,000 square feet (c) Minimum Frontage: 150 feet.
View Source
DIMENSIONAL STANDARDS. TABLE -1 below delineates the minimum residential lot dimensional standards established under the provisions of this Development Agreement: Minimum Lot Size 8,250 6,600 square feet Minimum Lot Width 75 60 feet (front setback line) Minimum Living Area 1,200 square feet Minimum Front Setback 20 feet Minimum Rear Setback 10 feet Minimum Side Interior Setback 7.5 5 feet Minimum Side Street Setback 15 feet Maximum impervious surface ratio (per lot) 0.75 Maximum Building Height*** 35 feet *** Residences bordering westerly property perimeter shall be limited to one (1) story.
View Source
DIMENSIONAL STANDARDS. All dimensional standards for each zoning classification as provided in Chapter 3, LDC shall apply, or in the case of a variance, the PLDRB shall resolve. unless otherwise specified in this document.
View Source
DIMENSIONAL STANDARDS. Residential Non-residential Min. Lot size n/a n/a Min. Lot width n/a n/a Impervious Surface Ratio 0.70 n/a Maximum FAR n/a 0.4’ n/a Max Building Height 60’* 45’* Building Setbacks Lot lines Roads Colbert ▇▇▇▇ ▇▇▇▇▇ Dr. Upland Buffer **** 0’ 20’ 35’*** 25’*** See footnote 0’ 20’ 35’*** 25’*** See footnote * The residential building(s) immediately abutting Blare Drive shall be limited to a maximum building height of 45’. ** Tract 505a: The building height and uses on this tract shall be consistent with the uses previously governed by the Grand Haven PUD, ORB 1010, Page 1293. *** See Landscape buffer requirements, LDC **** Upland Buffer - To ensure minimal impacts to off-site conservation lands, a minimum 25-foot averaged 50-foot upland buffer shall be provided on the western property boundary
View Source

Related to DIMENSIONAL STANDARDS

  • Technical Standards The Generation System shall be installed and operated by the Interconnection Customer consistent with the requirements of this Agreement; the Technical Requirements; the applicable requirements located in the National Electrical Code (NEC); the applicable standards published by the American National Standards Institute (ANSI) and the Institute of Electrical and Electronic Engineers (IEEE); and local building and other applicable ordinances in effect at the time of the installation of the Generation System.

  • Professional Standards The Contractor agrees to maintain the professional standards applicable to its profession and to consultants doing business in the United States Virgin Islands.

  • International Standards In determining whether an international standard, guide, or recommendation within the meaning of Articles 2 and 5 and Annex 3 of the TBT Agreement exists, each Party shall apply the principles set out in Decisions and Recommendations adopted by the Committee since 1 January 1995, G/TBT/1/Rev.8, 23 May 2002, Section IX (Decision of the Committee on Principles for the Development of International Standards, Guides and Recommendations with relation to Articles 2, 5 and Annex 3 of the Agreement), issued by the WTO Committee on Technical Barriers to Trade.

  • General Standards An Assistant Professor will be competent to teach in a particular field, will be current in the literature of that field, and will seek to meet student needs in both the classroom and in non-classroom environments. However, an Assistant may be a junior member of the academic community, with little professional and/or teaching experience. Furthermore, an Assistant may have little experience in curriculum development, committee work, governance, professional and/or community service, etc. In short, an Assistant Professor generally will be new to tenure-track college teaching. For eligibility for promotion from Assistant to Associate Professor, the candidate must have served a minimum of four (4) years at the rank of Assistant Professor, and must show evidence that he/she has grown professionally and consistently has sought to meet student needs, in both the classroom and in non-classroom environments. A successful candidate for the rank of Associate Professor will have remained current in the field, and will have improved his/her teaching in some demonstrable way. He/she also will have demonstrated professional growth in one or more of the following ways: completion of additional appropriate course work (if applicable), attendance at professional conferences, service on campus and/or District committees, professional and/or community service, or, the production of some creative work. Evidence of professional growth will be drawn from a careful analysis of student evaluations and peer evaluations over a period of time, and from a critical reading of materials submitted by the candidate. For promotion from Associate to Professor, the candidate must have served a minimum of four (4) years at the rank of Associate Professor, and must show evidence that he/she has grown professionally to a point where he/she has mastered both a particular field of knowledge and the teaching of that knowledge. A successful candidate must show evidence that he/she consistently has sought to meet student needs, in both the classroom and non-classroom environments. A Professor should be a senior member of the faculty, one who has such substantial experience, knowledge, and skill that he/she could mentor junior faculty in his/her area of expertise. A Professor will have demonstrated all the same kinds of achievements and attributes necessary for promotion to the Associate Professor rank, but in addition will demonstrate that he/she is a leader in some appropriate sense. Evidence of professional growth and leadership will be drawn from a careful analysis of student evaluations and peer evaluations over a period of time, and from a critical reading of materials submitted by the candidate.

  • General Standard Without prejudice to all other obligations of the parties under this contract, each party shall, in its dealings with the other for the purpose of, and in the course of performance of its obligations under, this contract, act with due efficiency and economy and in a timely manner with that degree of skill, diligence, prudence and foresight which should be exercised by a skilled and experienced: (a) network owner and operator (in the case of Network Rail); and (b) train operator (in the case of the Train Operator).